Nobody buys a house dreaming of the day they get to drain the water heater. And yet here you are, a homeowner, reading about sediment. Welcome. The good news: once a year, about an hour, and your water heater lasts longer, runs quieter and costs less to heat water.
This guide walks through yearly maintenance for both kinds of heater we install: a tank (like Bradford White and State) and a gas tankless (like the Rinnai RX199 and RXP199). It's based on the manufacturers' own guidance, written the way we'd explain it standing in your garage. And if at any point you'd rather hand it off, the last section is for you.
Read this before you touch anything
A water heater combines three things that don't forgive mistakes: scalding water, pressure, and either gas or 240 volts. Every step below assumes you've done these first.
- Turn the energy off first, every time. Electric: switch the water heater's breaker off at the panel (usually a double breaker). Gas: turn the gas control knob to "Off" or "Pilot" per the label on your heater, and know where its gas shutoff valve is. Tankless: unplug it or turn off its breaker, and turn off its gas supply valve.
- Let it cool. Tank water can be 120°F or hotter and will be for hours. Give it time, or at least wear gloves and eye protection and keep your face away from valves and hose ends.
- Never restore power to an empty electric tank. Elements that heat with no water around them burn out in seconds. The tank must be completely full first.
- Smell gas? Stop. Leave immediately and warn others. From a safe place, call 911 and Enbridge Gas North Carolina at 877-776-2427. Don't flip light switches, use phones inside, or try to fix it.
- Read your heater's label and manual. Models differ. When this guide and your manual disagree, the manual wins.
- When in doubt, don't. A stuck valve, a leak, a gas smell or a step that doesn't look like the description is your cue to stop and call a licensed plumber.
Has your tank gone 10 years without a flush? Skip the DIY flush.
This is the counterintuitive part. If your tank water heater is around 10 years old (or older) and has never been flushed, don't start now.
A decade of sediment settles in a thick layer on the bottom of the tank. Sometimes that layer is the only thing sealing small corrosion spots in the steel. Stir it up and drain it out, and a tank that was quietly getting by can start leaking from the bottom. On top of that, an old plastic drain valve that hasn't moved in ten years often won't close tightly again, and now you have a drip you didn't have this morning.
On a tank that old, the sediment has usually already done its damage. The better question is whether it's time to replace it. Our water heater page covers repair versus replace honestly and lists our installed prices, so you can make that call with real numbers.
How to flush a tank water heater
Do this once a year. Sediment (minerals that settle out of the water) collects on the bottom of the tank, where it insulates the water from the burner or elements. That's the popping and rumbling you hear, and it makes the heater work harder for the same hot water.
- A garden hose long enough to reach a floor drain or outdoors
- A bucket
- Work gloves and safety glasses
- A flathead screwdriver (some drain valves need one)
- About 45 minutes to an hour
- Easy, as long as the drain valve cooperates
- Best done after the water has cooled
- Turn off the energy. Electric: breaker off. Gas: gas control to "Off" or "Pilot" per the label. See the safety box above.
- Turn off the cold water supply at the valve on the pipe going into the top of the tank.
- Open a hot water faucet somewhere in the house, ideally the closest one. This lets air in so the tank drains instead of holding water by vacuum.
- Connect the hose to the drain valve near the bottom of the tank and run the other end to a floor drain, a sump, or outside, somewhere the water can't scald anyone or flood anything. Remember it may come out very hot.
- Open the drain valve slowly and let the tank drain. The first water out is often cloudy or gritty. That's the point.
- Stir up what's left. Once it slows, briefly open the cold supply valve for a few seconds, then close it again. The rush of water kicks loose sediment at the bottom. Repeat until the water runs clear into your bucket.
- Close the drain valve and remove the hose. Check that the valve isn't dripping.
- Refill the tank. Open the cold supply valve fully and leave the hot faucet open. When water flows steadily from that faucet with no sputtering air, the tank is full. Then close the faucet.
- Turn the energy back on, only after the tank is full. Electric: breaker on. Gas: follow the lighting instructions on the label.
- Check your work. Look for drips at the drain valve and fittings over the next hour, and give the heater some time to reheat before the household's next round of showers.
If the drain valve won't open, or won't close once it's open: don't force it. Old plastic valves crack. Close the cold supply, cap the valve with a garden-hose cap if it's dripping, and call us. A drain valve is a small repair; a cracked one at 9 p.m. is a long night.
Check the temperature-and-pressure relief valve
The T&P valve is the brass valve on the top or side of the tank with a lever and a pipe running down from it. If temperature or pressure inside the tank ever gets dangerous, it opens. It's the most important safety device on the heater.
- Make sure the discharge pipe is in place and runs down to within a few inches of the floor or to a drain, so anything that comes out is pointed away from people.
- Put a bucket under the end of the discharge pipe and stand to the side.
- Lift the lever briefly for a couple of seconds, then let it snap back. You should hear a rush and see hot water come out of the pipe. That water is scalding.
- Watch for a minute afterward. If water keeps dripping from the pipe, or nothing came out at all, the valve needs replacing. Call a plumber; don't cap or plug it.
Fair warning: on an older valve that hasn't been touched in years, testing it can be the thing that makes it start dripping. That isn't the test's fault; it found a valve that was already worn out. Better to find out now than in a real overpressure.
Check the anode rod (every few years)
The anode rod is a metal rod screwed into the top of the tank. Its job is to corrode so your tank doesn't. Water attacks the rod first; once the rod is used up, the water goes to work on the steel tank. Replacing a worn anode is one of the cheapest ways to get more years out of a tank.
Honest assessment: this one's harder than it sounds
Anode rods are often seized tight after years in the tank, they need a large socket and a lot of leverage, and many heaters don't have enough overhead clearance to pull a 40-inch rod straight out. If yours fights you, stop before you damage the fitting or the tank. This is a very reasonable thing to let us do.
- Turn off the energy and the cold water supply, exactly as for a flush.
- Relieve the pressure by opening a hot faucet, then drain a few gallons from the drain valve so the water level drops below the top of the tank.
- Find the anode. Look for a hex head on top of the tank, sometimes under a plastic cap. On some models it's built into the hot water outlet fitting instead; your manual shows which you have.
- Loosen and remove it with a socket (commonly 1-1/16") and breaker bar. Turn counterclockwise, and steady the tank so you're not twisting the whole heater.
- Inspect it. A healthy rod is thick and fairly even. Replace it if it's worn down to about half an inch thick, if several inches of the bare steel core wire are showing, or if it's caked with heavy deposits.
- Reinstall or replace using plumber's thread tape on the threads. Then refill the tank with a hot faucet open, check for leaks at the fitting, and only then restore the energy.
Got a rotten-egg smell from your hot water? That's often a reaction between the anode and bacteria in the tank, and a different style of anode usually fixes it. Ask us about it.
Set the temperature to 120°F
While you're there, check the thermostat. We set the heaters we install at 120°F. It's hot enough for showers and dishes, lowers the scald risk for kids and older adults, and saves energy. On an electric tank, the thermostats are behind access panels and the power must be off before you open them. On a gas tank, it's the dial on the gas control. On a Rinnai, it's the temperature controller.
How to flush a Rinnai tankless water heater
A tankless heater doesn't collect sediment in a tank; it collects scale inside its heat exchanger, the narrow passages that heat the water as it flows through. Raleigh and Cary water is soft (about 1.5 grains per gallon), so scale builds slowly here. But Rinnai requires a descaling flush once a year to keep the warranty in force, so this one isn't optional.
Your heater should have isolation valves installed below it: a cold valve (blue handle), a hot valve (red handle), and service ports on each with small T-handle purge valves and caps. If it doesn't have them, the flush can't be done this way, and that's a job for a plumber.
- 4 gallons of plain, undiluted white vinegar
- A 5-gallon bucket
- A small submersible utility pump
- Hoses that reach from the valves to the bucket (washing-machine hoses work)
- Your heater's manual
- About an hour, including about 45 minutes of circulating
- Moderate: easy once you've seen the valves
- Vinegar only. Rinnai warns never to use chemical cleaners; this is your drinking water.
- Turn off the power to the heater (unplug it or turn off its breaker) and turn off the gas supply valve to the heater.
- Close all three water valves: the cold valve, the hot valve, and the main supply valve feeding the heater.
- Remove the purge valve caps slowly. Make sure the hot valve is fully closed first, then unscrew the caps on the cold and hot purge ports a little at a time to let any pressure out. Keep the small rubber washers inside the caps; you need them to reseal.
- Connect the hoses. One hose runs from the cold-side purge port to the pump in the bucket. The other runs from the hot-side purge port back into the bucket. Pour the 4 gallons of vinegar into the bucket.
- Open both purge valves by turning the T-handles so they're perpendicular to the valve.
- Circulate. Turn on the pump and let the vinegar circulate through the heater for about 45 minutes, or as long as your manual specifies.
- Rinse. Turn off the pump. Following your manual, move the return hose to a drain and open the cold valve briefly to flush fresh water through and push the vinegar out.
- Close the purge valves by turning the T-handles back.
- Remove the hoses and screw the purge caps back on, snug but not overtightened, with the rubber washers in place.
- Clean the inlet water filter if your model has one. It's a small screen at the cold water inlet; your manual shows how to remove and rinse it.
- Restore service. Open the main supply, cold and hot valves as your manual describes, turn the gas back on, and restore power.
- Bleed the air. Open a hot faucet indoors and let it run slowly until water flows steadily with no sputtering, usually two or three minutes.
While you're at it: on gas units, brush dust and lint off the air intake filter or screen if your model has one, and on condensing models like the RX series, make sure the condensate drain line is clear. Check for leaks at the valves before you walk away.
Want the details on the RX199 and RXP199, including freeze protection? See our Rinnai tankless page. If your outdoor unit has ever frozen, read our frozen-pipe guide before winter.
Your yearly checklist
| Task | Tank | Tankless |
|---|---|---|
| Flush (sediment or scale) | Every year | Every year (required for Rinnai warranty) |
| Test the T&P relief valve | Every year | Per your manual |
| Inspect the anode rod | Every 2–3 years | Not applicable |
| Clean inlet water filter | Not applicable | Every year |
| Clean air intake and condensate line | Not applicable | Every year (gas condensing units) |
| Check temperature (120°F) | Every year | Every year |
| Look for leaks, rust and loose fittings | Every few months | Every few months |
Pro tip from the homeownership school of hard knocks: pick a date you'll remember, like the day the clocks change, and put it on the calendar. "I'll get to it" is how a water heater turns 12 without ever being flushed.
Frequently asked questions
How often should I flush my water heater?
Once a year for both tank and tankless heaters. Rinnai requires an annual descaling flush to maintain its warranty coverage.
Should I flush a water heater that's never been flushed?
If it's a tank around 10 years old or older, we don't recommend a DIY flush. Disturbing a decade of sediment can expose corrosion and start a leak, and an old drain valve may not reseal. At that age, it's usually time to look at replacement.
Can I use something stronger than vinegar on my tankless?
No. Rinnai's guidance is plain, undiluted white vinegar and never chemical solutions, because the water that runs through the heater is water you use.
Why is my water heater popping or rumbling?
That's usually sediment on the bottom of the tank, with water trapped underneath it boiling. A flush typically quiets it down. On a tank past 10 years, the noise often means the sediment has already done its damage.
How do I know if my anode rod needs replacing?
Pull it and look. If it's worn to about half an inch thick, the steel core wire is showing, or it's heavily caked, replace it. A rotten-egg smell in your hot water can also point to the anode.
Will ARC flush it for me?
Yes. A tank flush runs $250–$300 and a Rinnai annual flush is $273. If ARC installs your tank, the yearly ARC flush plan extends our warranty on it from 5 to 10 years, and your first tankless flush is free when you schedule it the day we install.
Or skip all of this. We'll handle it.
Reading about anode rods is one thing. Wrestling one out of a tank in a cramped closet is another. If you'd rather kick back while a licensed plumber flushes the heater, tests the relief valve, checks the anode and looks over the whole installation, give us a call. You keep the Saturday; we bring the hoses.
ARC Plumbing serves all of Wake County from our shop in Fuquay-Varina. In-home quotes during business hours are free: no trip charge, no estimate fee, and the price in writing before we start.
ARC Plumbing · 2406 Waco Commercial Ct, Fuquay-Varina, NC 27526 · NC Plumbing Contractor License #36473 · Rinnai PRO contractor
Tankless steps adapted from Rinnai's guide to flushing a Rinnai tankless water heater. Tank maintenance items follow Bradford White's water heater maintenance tips. Always follow the manual for your specific model.
